top of page
.png)
MASTER LIST
Complete each step in the order provided.
Do not skip any steps.
STEP 1: GATE
GATE
STEP 1:
UNLOCK THE GATE
Use the code you were provided to unlock the padlock.
RELOCK THE PADLOCK ONTO THE GATE
SECURE THE GATE
Attach the gate to the wall and fence using the chains.
STEP 2: PARKING LOT DOOR
PARKING LOT DOOR
TO UNLOCK
Enter your code on the keypad, then press the ULTRALOQ logo.
TO LOCK
Press the ULTRALOQ logo.
STEP 2:
STEP 3: DISARM ALARM
ALARM - UNARM
STEP 3:
LOCATE KEYPAD
When you enter through the parking lot door the keypad will be on the wall to your right.
ENTER YOUR CODE AND PRESS 'STANDBY' TO DISARM
Disarm within 60 secs or alarm will sound.
i
EMERGENCY CONTACT
If alarm does not and the countdown beeps call: 365-675-4200
STEP 4: SHAW ST GARAGE
SHAW ST GARAGE
STEP 4:
UNLOCK THE PADLOCK
Use the code you were provided to unlock the padlock.
UNLOCK CANE BOLT
From the inside, pull up the cane bolt and then slide the garage door to the right to open.
STORE THE PADLOCK
Leave the padlock on ledge beside door shown in image.
STEP 5: PARKING LOT GARAGE DOOR
PARKING LOT GARAGE DOOR
STEP 5:
UNLOCK DOOR
Slide the 2 metal levers on the left and right of the door open
OPEN THE DOOR
Use the rope to lift and open the door
STEP 6: SHAW ST DOOR
OPENING - SHAW ST DOOR
STEP 6:
SHAW DOOR
Shaw Ave door locks automatically. To keep it unlocked, put a zip tie on the door handle.
PARKING
PARKING
EVIL EMPIRE PARKING
Only park in the 'Evil Empire Parking' spaces or the loading zone in front go the garage door. Do not park in Crown labeled spaces.
CARS INSIDE WAREHOUSE
Vehicles can enter the building using the Shaw St. garage door
PAID PARKING
Paid parking is across the street off of Victoria Ave.
WAREHOUSE LIGHTS
WAREHOUSE LIGHTS
LOCATE REMOTE
Light remote is located in the mesh container on the centre beam
PIN POINT WHICH LIGHTS TO CONTROL
The remote controls the lights in the Warehouse and the Dark Studio. Point the remote up at the lights you want to control.
i
To only control the warehouse lights place yourself in the warehouse behind the shipping container and point the remote at the warehouse lights
HEATING
HEATING
TURNING HEAT ON/OFF
Use the wooden stick beside the breaker panel and flip the 2 light switches above the breaker:
UP = ON
DOWN = OFF
TURN OFF TUBE HEATERS
Use the breaker panel between the container and wall to turn off Tube Heater. Its labeled "Tube Heater" on the bottom left of the panel
i
Temperature is controlled by Google Nests and sets to 21° during shoot days. To change temperature message 365-675-4200. Do not change the temp or turn it up. It won't increase faster.
FANS
FANS
LOCATE REMOTE
Remote is located on the middle beam.
Fan Icon = ON/OFF
+/- Icon = SPEED
i
Fans help to distribute the heat so turn when you can if space feels cold
BREAKER PANELS
BREAKER PANELS & STUDIO POWER
BREAKER PANELS
Panel 1: located on the white wall in centre area near office containers
Panel 2: located around the corner from panel 1 between the container. and wall
POWER
The studio has 2x 15 amp plugs and 2x 20 amp plugs located on the centre beam.
DUNGEON POWER
DUNGEON POWER
RUNNING POWER TO DUNGEON
You will need to run AC power cords (100 ft) from the centre beam to the basement.
ADDITIONAL PLUG
There is 1x plug near the dungeon basement door and 1x plug at the top of the stairs inside the Dungeon entrance
TUNNEL POWER
TUNNEL POWER
RUNNING POWER TO TUNNELS
You will need to run AC power cords (100 ft) from the centre beam to the basement.
ADDITONAL PLUG
There are two plugs in the entrance stairwell to the tunnels.
POWER ACCESS
A hole in the warehouse floor can be used to route power cables into the tunnels. The cover, which resembles a drain grate, must be removed to access the opening. This is not an active drain, and there is no risk of water exposure to the cables.
VIDEO VILLAGE
Video Village will need to be near the opening of the tunnels to get signal. We can clear the stairs before your shoot to accomidate this.
WATER
WATER
HOSE HOOK UP
The hose drop is behind the container in front of the dungeon entrance. Plug the hose into the spool on the floor and turn on the valve at the end.
bottom of page